2-TOPSHIRIQ
Cisco Packet Tracer dasturida statik marshrutlash.
Cisco Packet Tracer dasturida glabal tarmoq qurib statik marshrutlash qiling. (ishning natijasi screen qiling va routerga kirib CLI komandasida “Router>enable” dan boshlab copy qilib oling).
Cisco Packet Tracer dasturida dinamik marshrutlash.
Cisco Packet Tracer dasturida glabal tarmoq qurib dinamik marshrutlash qiling. (ishning natijasi screen qiling va routerga kirib CLI komandasida “Router>enable” dan boshlab copy qilib oling).
Cisco Packet Tracer dasturida kichik o‘lchamli korporativ tarmog‘ini loyihalash.
Cisco Packet Tracer dasturida servar va boshqa qurilmalar yordamida kichik o‘lchamli korporativ tarmoq quring va ishlash jarayonini tekshiring. (ishning natijasini screen qilib oling).
Cisco Packet Tracer dasturida katta o‘lchamli korporativ tarmog‘ini loyihalash.
Cisco Packet Tracer dasturida servar va boshqa qurilmalar (Vlan) yordamida katta o‘lchamli korporativ tarmoq quring va ishlash jarayonini tekshiring. (ishning natijasini screen qilib oling).
Cisco Packet Tracer dasturida TelNET protokoli bilan ishlash.
Cisco Packet Tracer dasturida qurilmadan Telnet protokolidan foydalanib switch konfiguratsiyasiga kirish. (ishning natijasini screen qilib oling. Switchga kirib CLI komandasida “Switch>enable” dan boshlab copy qilib oling).
Cisco Packet Tracer dasturida statik marshrutlash.
Cisco Packet Tracer dasturida glabal tarmoq qurib statik marshrutlash qiling. (ishning natijasi screen qiling va routerga kirib CLI komandasida “Router>enable” dan boshlab copy qilib oling).
Avvalambor taqmoqni joylashuvlarini songra kampyuterlarni ip adreslarini o’rnatib chiqamiz. Shuningdek qaysi ip orqali global tarmoqqa chiqishini xam kiritamiz
Xar ikki routerga shu amal bajariladi
Router>en
Router#config
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int gig 0/0
Router(config-if)#ip 10.0.0.1 255.255.0.0
^
% Invalid input detected at '^' marker.
Router(config-if)#ip address 10.0.0.1 255.255.0.0
Router(config-if)#no shutdown
Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up
Router(config-if)#exi
Router(config)#int se0/0/0
Router(config-if)#ip address 173.0.0.1 255.255.0.0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to down
Router(config-if)#
Router(config-if)#exit
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up
Router#en
Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#ip route 20.0.0.0 255.255.0.0 173.0.0.0
Router(config)#esit
^
% Invalid input detected at '^' marker.
Router(config)#exit
Router#
|
