Release history Readme file for SuperSequencer Evaluation software

Windows 2000

500 MHz Processor

80 Meg free disc space

256Mb RAM
Minimum viewing resolution

800 x 600 High colour (16 bit)

Created November 3rd 2004

************************

1. MARGINING Window.

Improvements - Margining window includes a calculator and test window.

Version 2.0.6

Created January 3rd 2005

************************

Improvements - Included support for ADM1068/69 Old and new bond out

Version 3.0.1

Created January 25th 2005

*************************
1. ADM106x Software

Fixed the sequencing engine restart problem - Bit0 of SECTRL register was getting set when

downloading to EEPROM.
2. "Recall Off-Line Settings From File"

Improvements - Better reporting when recalling files.

Improvements - All checksum data locations are now labelled in the file.

Bug fix - Labelling Bug in the "Pull up supply" dropdown box when configuring

ADM1068/69
5. INPUTS Window

Bug fix - When configuring an ADM1068/69 VX4 was set to digital mode

regardless of what was in the configuration register.
6. REGISTER ACCESS Window

Bug fix - Register reporting labels were incorrect When configuring an

ADM1068/69. All register labels are now correct.
7. MARGINING Window.

Bug fix - No reporting of DAC voltages when entering the window.

Improvements - Full control of DACs independent of the calculator window.

Improvements - All data from the window can be saved and recalled from file.

Improvements - Inclusion of multi device select options

Version 3.0.2

Created March 31st 2005

***********************

Bug fix - Contents of register PDEN1 not saved to file. * Checksum errors may occur when

recalling pre version 3.0.2 text files.
2. "Recall Settings From File"

Bug fix - PDEN values overwritten when file is recalled.

Bug fix - When configuring an ADM1068/69 the register access window only displayed

values for device address 9E.
4. ADM106x Software

Improvements - Reduced overall CPU usage.

Improvements - Increased sequencing engine update speed.

Improvements - Sequencing Engine program is able to be expanded to display a

greater number of states. This is a read only function and cannot be edited.

7. SEQUENCING ENGINE Window

Bug fix - Pasting data into state 63 did not work.
8. ADM106x Start Up

Improvements - Better reporting when recalling state and pin names from last saved session.

Improvements - Enhanced multi device select options

Improvements - Better reporting on Silicon version and ADM1068/69 bond out status

Bug - VP3 Input range incorrect.

Improvements - 'Do not show again' may be set in the main window and re-enabled in the main

menu.
13."Save Configuration Version To EEPROM"

Improvements - This function can now be used in off line mode. It is launched when a save to

file is initiated.
14.ADM106x software

Device search can be initiated on-line or off-line.

Improvements - Sequencing engine window includes Sequence Engine debug tool.

Bug fix - Data was not retained when setting up of the digital registers offline.

Version 3.0.3 to 3.0.5 NOT RELEASED

***********************************

Version 3.0.6

Created March 31st 2006

***********************
1. DEBUG TOOL Window

Bug fix - Debug tool could not differentiate between digital input and analog input.

Bug fix - Unable to Jump state when SMBus Jump was used as part of the Sequence.

Information on recommended pull-up resistors when SCL or SDA button is pressed

Bug fix - Current sink symbol gave the impression that data had changed when switching between inputs.

Bug fix - some instability with the pull-down strength selection when switching between windows.

Improvements - Added an additional display window showing Intel hex master checksum.

Bug fix - AUX1 and AUX 2 were not included in the drop down list for "Selected input".

Bug fix - Potential divide data for VX1-5 and AUX 1-2 not saved to file.

Bug fix - Instability on DAC 1 when using the test window.

Improvements - Ability to switch between multiple devices on the bus without restarting the SE.

Improvements - Added the ability to program multiple devices using a daisy chain method.

Bug fix - Checksum error occurred when the line checksum was equal to x00h because A 16 bit value

was being used as the line checksum instead of an 8 Bit value.
13. SEQUENCING ENGINE Window

Bug fix - In multi device mode, the State names were not saved when insert state was used.

Bug fix - In multi device mode, the SE data was not saved when switching between parts.

Bug fix - The data for the potential divide was recalled when asked if the operator wished to recall Pin names,

State names and margining data on start up.
16. REGISTER ACCESS Window

Bug fix - The UV and OV fault status were reversed.

Bug fix - The 'DAC on' button and the Target margining data would be difficult to set when more than one channel

was margining.
18. SEQUENCING ENGINE Window

Improvements - Added a PDO zoom window which is launched using the blue button labelled 'Output’ on the program

editor.
19. OUTPUTS Window

Bug fix - Changed 'Open Collector' to 'Open Drain' in the drop down box

Bug fix - When recalling a text file Pin names and state names were not recalled into the SE window.

Improvements - Increased the resistor input field to two decimal places to allow the input values for high

accuracy resistors.
22. MARGINING Window

Bug - The offline DAC configuration using an ADM1069 was not working correctly.

Improvements - The readback window now includes a data logger to file.(Excel or text)

Improvements - Label change of the VX digital pins from 'Digital Fault Detector' to 'Digital Inputs'

Improvements - The SE window now has a display to show what state the SE is currently in.

Created May 17th 2006

*********************
1. SEQUENCING ENGINE Window

Bug - When switching between multiple parts the Sequence Engine window did not upload the correct data into the window.

Also occurred when recalling files.

Version 4.0.0

Created May 1st 2007

********************

1. Installation

- Able to manage license agreement on non-Administrator accounts.
2. Pin Names Window

- No Longer possible to 'tab' to hidden pin names text entry fields.

- Configuration version numbers that contain leading zeros now display correctly on the screen. Leading zeros have always been stored correctly in EEPROM, only the display in software was affected.
3. Margining Window

- Many changes to the target value limiting code used to control the DAC output to ensure the correct range is available.

- Incorrect mapping of ADC's when using an ADM1069 has been fixed.
4. Log Files

- Extra lines between data points have been removed.

- User is now warned if the file they are trying to log to can not be opened for writing.
5. Register Access Window

- Numerous cosmetic fixes to prevent inadvertent text entry, and register bit view update issues.

- Fixed the name of the PS1VOTH register, changed a zero to an 'O'.

- Labelling was incorrect for status registers.

- When deleting a state a modified dialog window is used to prevent the window being too large for the screen if there is a state that references or is referenced by a large number of other states.

- No longer possible to select the '-------' menu option in the Sequence state definition.

- Additional bounds checking on the Sequence state list to ensure that there are always no more than 63 user editable state present.

- Hid additional output labels in the 'Output Zoom' window when using devices with only eight outputs.

- Additional communication checks during SE debug mode to check communication with device is operating correctly.

- User modification of the evaluation board settings is now locked out for a few seconds upon entering the view to allow the software to update the settings. This is to prevent the case where a user quickly made a change to a control which was immediately overwritten and ignored.

- If communications is lost with a device, and the user tries to recall a file from disk to download to the device it is no longer possible to select a file.

- When working with the ADM1065 offline and saving a configuration to disk correct values are now written to the DACx and DPLIMx registers and EEPROM. Files will now load correctly into an online ADM1065 session.

- The last data location in the SE EEPROM was not include in the checksum calculation.

- An ADM1068 - 9 file can no longer be recalled into anADM1062 - 67 device. An ADM1062 - 67 file can no longer be recalled into anADM1068-69 device both online and offline.

- There is no longer a forced single read when entering the window.

- There is no longer a wait for GO bit to clear in continuous read mode.

Changes

1. Software now supports an ADI USB to IIC converter dongle as an additional method of communication with an evaluation board or micro-evaluation board. This is an alternative to using the parallel to IIC converter cable where a PC does not have a parallel port.

1. Plugging an Evaluation board into an external non-powered USB hub can cause a machine to hang due to the power requirements of the board. It is recommended to always plug the board into a USB port directly on the host PC.

Version 4.0.1

Created May 10th 2007

*********************

1. "Save Settings To File" and " Save Off-Line Settings To File"

Bug - The Intel Hex checksum calculation was incorrect. The first line checksum of each EEPROM block was omitted from the calculation.
2. "Save Off-Line Settings To File"

Bug - The Intel hex checksum was different when saved multiple times. The master checksum variable was not reset after each save.

Version 4.0.2

Created May 28th 2007

*********************
Bug Fixes

1. Installation

- Unable to uninstall previous versions of ADM106x software. This is now fixed but will not uninstall version 4.0.0 and 4.0.1. This will require the user to manually uninstall these versions by following the steps shown below:

1. GOTO

2. GOTO

3. GOTO

4. Highlight ADM106x Configuration Tool V4.0.0 or 4.0.1 and press "Remove"
2. Log Files

- The software was not handling the opened files correctly and was responsible for multiple open files.

Now the software only opens one file and closes it after logging is complete.

Version 4.0.3

Created August 13th 2007

************************

1. In the register access window the 'update register' button only appears if the 'fault or status register' is selected from the tree.

1. When single/multiple devices are connected and the software is gathering data from them during the initialization phase of the software the state machine is paused, but is no longer reset by the software.

Version 4.0.4

Created October 16th 2007

*************************

1. The state machine would reset when using the "upload device EEPROM contents to PC" function

Version 4.0.5

Created June 27 2008

*************************

1. An output option has been added to allow the user to visualize state machines in a graphical form. An open source tool called 'Graphviz' has been included as part of the installer and is used to automatically generate a PDF, JPEG, PNG or SVG format file that shows the relationship between the different states, and the different transistions between them. On the 'Sequence Engine' view tab, click the 'Create State Diagram' button to being the process.

1. Display issues relating to fonts on certain machines have been fixed. The font used by all controls has been reviewed and changed where necessary.

Version 4.0.6

Created August 20 2009

**********************

1.Error in the state diagram. The warnings condition was inverted.

Version 4.1.0

Created August 19^th, 2010

**********************
1. New Feature – Now supports the ADM116x family of SuperSequencer devices that include non-volatile fault recording.
2. Changed - The software now uses a different driver to access the USB-SMBUS-CABLEZ USB to IIC Converter dongle. This requires the ADMxxxx run-time be installed as this provides access to the new driver. Refer to the document 'Updating USB-IIC Dongle Driver' in the Common folder of the Analog Devices entry in the Start menu for more details.

Version 4.1.1

Created February 1^st, 2011

**********************

1. 
   Configuration files generated on computers using a locale setup to use something other than a period (‘.’) to indicate a decimal point no longer causes a problem when loaded on a system that does use a period for the decimal point.
   
2. 
   When saving files in online mode, and reloading them in offline mode, the margining window now correctly reflects the configuration of the DAC. The DAC settings were being programmed and stored correctly in the file and device, but were not being updated correctly on the screen, unless the user had viewed the Margining tab while in Online mode.
   

Version 4.2.0

Created February 20^th 2012

**********************

1. 
   Added support for the USB-SDP-CABLEZ interface cable.
   

1. 
   Fixed a problem determining device type when loading files due to use of different decimal point in locales.
   
2. 
   Fixed an issue reporting correct device type in file, when in offline mode and when active device and device in file did not match.
   
3. 
   Fixed an issue with recognizing and initializing the USB-I2C dongle in virtual machine environments. In such environments, the dongle must be set to automatically connect to the virtual machine otherwise the dongle initialization process will fail.
   
4. 
   Closing the ‘User and Black Box EEPROM’ Window using the ‘X’ control no longer causes the software to become unresponsive.
   

Version 4.2.1

Created June 6^th 2012

**********************

1. 
   Fixed a problem with detecting I2C interfaces, where if the USB-SDP-CABLEZ interface had never been connected to a PC, it could prevent other I2C interfaces from being detected.
   

Version 4.2.2

Created October 31^st 2013

**************************

1. 
   When viewing the Black Box information on ADM1168 and ADM1169 devices, if the VP1 input had a UV SFD fault, this would not be decoded correctly in the table view. The contents of the Black EEPROM held the correct values, and were not affected by this bug.
   
2. 
   Fixes an issue with generating Excel format files on 64-bit platforms.
   

Version 4.2.3

Created November 28^th 2014

**************************

1. 
   Fixes an issue where monitor conditions for non-existent inputs on 8-channel models are enabled under some conditions, causing undesirable state machine behavior. It is recommended to reload configurations in this version of this software, view the sequence engine, and re-save the file to ensure this is not an issue if using 8-channel devices.