• R0, R1 va R2 da RIP ni sozlash
    		•

    «Tarmoq xavfsizligi»




    Download 12,81 Mb.
    bet23/73
    Sana23.05.2024
    Hajmi12,81 Mb.
    #251629
    1   ...   19   20   21   22   23   24   25   26   ...   73
    Bog'liq
    «Tarmoq xavfsizligi»

    Amaliy qism
    Uchta Router qurilmadan iborat tarmoq uchun RIP 2-versiyasini sozlash.
    Bizning vazifamiz rasmda ko‘rsatilgan tarmoq qurish va marshrutlashni sozlash. (9.2.Rasm)

    9.2-rasm. Cisco Packet Tracer dasturi maydonida tarmoq sxemasi

    Izoh: Tarmoqni sozlashda portlarni yoqishni unutmang.


    Tarmoq quriladi va har bir qurilma rasmda ko’rsatilganidek mos IP manzil beriladi.
    Routerlar (R0, R1, R2) ham mos IP manzil kiritiladi.

    9.2-rasm. Routerlarga IP manzil kiritish


    R0, R1 va R2 da RIP ni sozlash

    1. Routerlar ketma-ket tanlanadi, konfigutarsiya oynasidan RIP bandi tanlanadi va routerlarga tegishli IP manzillar kiritiladi (9.3-rasm).


    9.3-rasm. Router0 ga RIPni solash uchun interfeys yordamida routerlar IP manzilini kiritish
    2) Yoki CLI oynasiga quyidagi kod kiritiladi:
    Router(config)#router rip
    Router(config-router)#network 10.0.0.0
    Router(config-router)#network 11.0.0.0
    Router(config-router)#network 12.0.0.0
    Router(config-router)#network 192.168.2.0
    Router(config-router)#network 192.168.3.0
    Router(config-router)#

    9.4-rasm. Router1 ga RIPni solash uchun interfeys yordamida routerlar IP manzilini kiritish
    CLI oynasidagi kod quyidagicha bo’ladi:
    Router#configure terminal
    Enter configuration commands, one per line. End with CNTL/Z.
    Router(config)#router rip
    Router(config-router)#network 10.0.0.0
    Router(config-router)#network 11.0.0.0
    Router(config-router)#network 12.0.0.0
    Router(config-router)#network 192.168.1.0
    Router(config-router)#network 192.168.3.0
    Router(config-router)#
    Router(config-router)#end

    9.5-rasm. Router2 ga RIPni solash uchun interfeys yordamida routerlar IP manzilini kiritish
    CLI oynasidagi kod quyidagicha bo’ladi:
    Router>enable
    Router#
    Router#configure terminal
    Enter configuration commands, one per line. End with CNTL/Z.
    Router(config)#interface GigabitEthernet0/0/2
    Router(config-if)#
    Router(config-if)#exit
    Router(config)#router rip
    Router(config-router)#network 10.0.0.0
    Router(config-router)#network 11.0.0.0
    Router(config-router)#network 12.0.0.0
    Router(config-router)#network 192.168.1.0
    Router(config-router)#network 192.168.2.0
    Router(config-router)#
    Router(config-router)#end

    Download 12,81 Mb.
    1   ...   19   20   21   22   23   24   25   26   ...   73




    Download 12,81 Mb.