|
5 -amaliy ish mavzu: ospf, rip. Eigrp va bgp protokollari asosida dinamik marshrutlashni sozlash
|
| bet | 2/2 | | Sana | 26.02.2024 | | Hajmi | 0.52 Mb. | | #162620 |
Bog'liq 5-Amaliy ish 1. Anketa (talabalar), 3-mavzu, conference, 12 labaratoriya ishi, Маълумотлар тузилмаси ва алгоритмлар узб, Abduvositaka, Saralash algoritmlari, Akademik yozuv 2 Omonboyev Rashidbek 12, kontakt hodisalar, golosariy, Operatsion tizimlar uz, 1 - lesson (internet), 2-маруза мавзуси Симулятор, dars tahlili, 6666666666666666666666666666666666666Amaliy qism
Uchta Router qurilmadan iborat tarmoq uchun RIP 2-versiyasini sozlash.
Bizning vazifamiz rasmda ko‘rsatilgan tarmoq qurish va marshrutlashni sozlash. (5.2.Rasm)
5.2-rasm. Cisco Packet Tracer dasturi maydonida tarmoq sxemasi
Izoh: Tarmoqni sozlashda portlarni yoqishni unutmang.
Tarmoq quriladi va har bir qurilma rasmda ko’rsatilganidek mos IP manzil beriladi.
Routerlar (R0, R1, R2) ham mos IP manzil kiritiladi.
5.3-rasm. Routerlarga IP manzil kiritish
R0, R1 va R2 da RIP ni sozlash
Routerlar ketma-ket tanlanadi, konfigutarsiya oynasidan RIP bandi tanlanadi va routerlarga tegishli IP manzillar kiritiladi (5.4-rasm).
5.4-rasm. Router0 ga RIPni solash uchun interfeys yordamida routerlar IP manzilini kiritish
2) Yoki CLI oynasiga quyidagi kod kiritiladi:
Router(config)#router rip
Router(config-router)#network 10.0.0.0
Router(config-router)#network 11.0.0.0
Router(config-router)#network 12.0.0.0
Router(config-router)#network 192.168.2.0
Router(config-router)#network 192.168.3.0
Router(config-router)#
5.5-rasm. Router1 ga RIPni solash uchun interfeys yordamida routerlar IP manzilini kiritish
CLI oynasidagi kod quyidagicha bo’ladi:
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#router rip
Router(config-router)#network 10.0.0.0
Router(config-router)#network 11.0.0.0
Router(config-router)#network 12.0.0.0
Router(config-router)#network 192.168.1.0
Router(config-router)#network 192.168.3.0
Router(config-router)#
Router(config-router)#end
5.6-rasm. Router2 ga RIPni solash uchun interfeys yordamida routerlar IP manzilini kiritish
CLI oynasidagi kod quyidagicha bo’ladi:
Router>enable
Router#
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface GigabitEthernet0/0/2
Router(config-if)#
Router(config-if)#exit
Router(config)#router rip
Router(config-router)#network 10.0.0.0
Router(config-router)#network 11.0.0.0
Router(config-router)#network 12.0.0.0
Router(config-router)#network 192.168.1.0
Router(config-router)#network 192.168.2.0
Router(config-router)#
Router(config-router)#end
PC1 va PC2 o‘rtasidagi aloqani tekshirish
Mashrutlash to‘g‘ri bajarilganligini tekshirish (5.7-rasm).
9.7.Rasm. PC1-dan PC2-ga Ping
Tarmoqda RIP to’g’ri sozlanganini tekshirish uchun kompyuterlarga ma’lumot ko’natishni simulyatsiya jarayonida ham tekshirib olish kerak.
Topshiriq
Cisci Packet Tracer dasturida 2 ta, 3 ta routerlar bilan tarmoq quring va RIP protokolini sozlang. Tarmoqni to’g’ri sozlangani tekshiring va testdan o’tkazing
|
| |
