• B10.3.2.2 SCSI Parallel Interface (SPI-3) [NCITS.336:2000] standard
  • B10.3.4 SCSI Controllers/Devices - Windows Experience
  • B10.3.4.3 Windows XP/Windows 2000/Windows Me: Large partition support (>8 GB) and ability to boot from loader
  • B10.3.4.6 Controller and peripherals implement SCSI bus data protection signal
  • B10.3.4.8 Option ROM supports virtual DMA services
  • B10.3.1 SCSI Controllers/Devices - Windows Compatibility




    Download 1,03 Mb.
    bet197/250
    Sana21.03.2017
    Hajmi1,03 Mb.
    #428
    1   ...   193   194   195   196   197   198   199   200   ...   250

    B10.3.1 SCSI Controllers/Devices - Windows Compatibility

    B10.3.1.1 SCSI Configured Automatically (SCAM) support is disabled by default

    [SCSI-0113; SDG3:171]

    B10.3.2 SCSI Controllers/Devices - Industry Standards

    B10.3.2.1 Small Computer Interface (SCSI-2) [X3.131:1994] standard

    Global Engineering Documents at http://global.ihs.com/.
    B10.3.2.2 SCSI Parallel Interface (SPI-3) [NCITS.336:2000] standard

    [SCSI-0104]

    Global Engineering Documents at http://global.ihs.com/


    B10.3.3 SCSI Controllers/Devices - Quality

    B10.3.3.1 Passes WHQL tests

    See B1.3, B10.1.3.2, and B10.1.4.7.

    Windows XP: See “SCSI Controllers” and device-specific topics in HCT documentation.

    B10.3.4 SCSI Controllers/Devices - Windows Experience

    B10.3.4.1 Windows 98/Me: Driver runs in 32-bit protected mode after installation

    [SYS-0025]
    B10.3.4.2 Windows XP/Windows 2000: S3 and hibernation support

    [SYS-0003.4]

    Windows Me: Hibernate is not supported for SCSI.
    B10.3.4.3 Windows XP/Windows 2000/Windows Me: Large partition support (>8 GB) and ability to boot from loader
    B10.3.4.4 Adapter is capable of sharing IRQ and works behind a PCI-PCI bridge

    [SCSI-0106; SDG3:35]
    B10.3.4.5 Connector and terminator requirements

    [SCSI-01xx; SDG3:16x,170]

    • Bus type is clearly indicated using ANSI-approved icons on connectors for all adapters and peripherals. [SCSI-0108; SDG3:163]

    • Differential devices support DIFFSENS as defined in SPI -3 standard. [SCSI-0109; SDG3:164]

    • Automatic termination circuit and SCSI terminators meet SPI-3 standard. [SCSI-0110; SDG3:165]

    • Terminator power is supplied to the SCSI bus with overcurrent protection. [SCSI-0111; SDG3:166]

    • External connector meets SCSI-2 or later standard. [SCSI-0108; SDG3:167]

    • Controller and peripheral connections include Pin 1 cable designation; shielded device connector meets SCSI-2 or later standard. [SCSI-0108; SDG3:169]

    • External devices use automatic termination or an accessible on-board termination switch. [STOR-0345; SDG3:170]

    Note: Not required for Fault-Tolerant RAID devices where the terminators are considered to be a Field Replaceable Unit (FRU).

    • SCSI devices that support hot-plugging comply with Annex D of SPI-3. [SCSI-0104; SDG3:174]
    B10.3.4.6 Controller and peripherals implement SCSI bus data protection signal

    [SDG3:168]
    B10.3.4.7 Hardware supports the SCSI-3 START STOP UNIT command to decrease power consumption as defined in the SCSI Block Commands Specification

    [STOR-0346; SDG3:172]
    B10.3.4.8 Option ROM supports virtual DMA services

    [SCSI-0105; SDG3:146]
    B10.3.4.9 SCSI erasable drive supports SCSI commands

    [SDG3:183]
    B10.3.4.10 SCSI controller provides multi-initiator support if the controller provides external device connection capability for use as a cluster node

    [SCSI-0114; SDG3:162]

    Download 1,03 Mb.
    1   ...   193   194   195   196   197   198   199   200   ...   250




    Download 1,03 Mb.

    Bosh sahifa
    Aloqalar

        Bosh sahifa



    B10.3.1 SCSI Controllers/Devices - Windows Compatibility

    Download 1,03 Mb.