Questions 30-37
Do the following statements agree with the information given in Reading Passage 2?
In boxes 20-26 on your answer sheet, write
TRUE
if the statement agrees with the information
FALSE
if the statement contradicts the information
NOT GIVEN
if there is no information on this
30
The FAA was created as a result of the introduction of the jet engine.
31
Air Traffic Control started after the Grand Canyon crash in 1956.
32
Beacons and flashing lights are still used by ATC today.
33
Some improvements were made in radio communication during World War II.
34
Class F airspace is airspace which is below 365m and not near airports.
35
All aircraft in Class E airspace must use IFR.
36
A pilot entering Class C airspace is flying over an average-sized city.
42
READING PASSAGE 8
Sheet glass manufacture: the float process
Glass, which has been made since the time of the Mesopotamians and Egyptians, is little more than a mixture
of sand, soda ash and lime. When heated to about 1500 degrees Celsius (°C) this becomes a molten mass that
hardens when slowly cooled. The first successful method for making clear, flat glass involved spinning.
This method was very effective as the glass had not touched any surfaces between being soft and becoming
hard, so it stayed perfectly unblemished, with a 'fire finish'. However, the process took a long time and
was labour intensive.
Nevertheless, demand for flat glass was very high and glassmakers across the world were looking for
a method of making it continuously. The first continuous ribbon process involved squeezing molten glass
through two hot rollers, similar to an old mangle. This allowed glass of virtually any thickness to be made non-
stop, but the rollers would leave both sides of the glass marked, and these would then need to be ground and
polished. This part of the process rubbed away around 20 per cent of the glass, and the machines were very
expensive.
The float process for making flat glass was invented by Alistair Pilkington. This process allows the
manufacture of clear, tinted and coated glass for buildings, and clear and tinted glass for vehicles. Pilkington
had been experimenting with improving the melting process, and in 1952 he had the idea of using a bed of
molten metal to form the flat glass, eliminating altogether the need for rollers within the float bath. The metal
had to melt at a temperature less than the hardening point of glass (about 600°C), but could not boil at a
temperature below the temperature of the molten glass (about 1500°C). The best metal for the job was tin.
The rest of the concept relied on gravity, which guaranteed that the surface of the molten metal was perfectly
flat and horizontal. Consequently, when pouring molten glass onto the molten tin, the underside of the glass
would also be perfectly flat. If the glass were kept hot enough, it would flow over the molten tin until the top
surface was also flat, horizontal and perfectly parallel to the bottom surface. Once the glass cooled to 604°C or
less it was too hard to mark and could be transported out of the cooling zone by rollers. The glass settled to a
thickness of six millimetres because of surface tension interactions between the glass and the tin. By fortunate
coincidence, 60 per cent of the flat glass market at that time was for six-millimetre glass.
Pilkington built a pilot plant in 1953 and by 1955 he had convinced his company to build a full-scale plant.
However, it took 14 months of non-stop production, costing the company £100,000 a month, before the plant
produced any usable glass. Furthermore, once they succeeded in making marketable flat glass, the machine
was turned off for a service to prepare it for years of continuous production. When it started up again it took
another four months to get the process right again. They finally succeeded in 1959 and there are now float
plants all over the world, with each able to produce around 1000 tons of glass every day, non-stop for around
15 years.
Float plants today make glass of near optical quality. Several processes - melting, refining, homogenising -
take place simultaneously in the 2000 tonnes of molten glass in the furnace. They occur in separate zones in
a complex glass flow driven by high temperatures. It adds up to a continuous melting process, lasting as long
as 50 hours, that delivers glass smoothly and continuously to the float bath, and from there to a coating zone
and finally a heat treatment zone, where stresses formed during cooling are relieved.
43
The principle of float glass is unchanged since the 1950s. However, the product has
changed dramatically, from a single thickness of 6.8 mm to a range from sub-millimetre to 25 mm, from a
ribbon frequently marred by inclusions and bubbles to almost optical perfection. To ensure the highest quality,
inspection takes place at every stage. Occasionally, a bubble is not removed during refining, a sand grain
refuses to melt, a tremor in the tin puts ripples into the glass ribbon. Automated on-line inspection does two
things. Firstly, it reveals process faults upstream that can be corrected. Inspection technology allows more than
100 million measurements a second to be made across the ribbon, locating flaws the unaided eye would
be unable to see. Secondly, it enables computers downstream to steer cutters around flaws.
Float glass is sold by the square metre, and at the final stage computers translate customer requirements into
patterns of cuts designed to minimise waste.
|
